If all you want is a watch that has that iced out, bust down look, and don’t want to spend much money, then Pintime watches are going to be a good choice. They do possess that look, and at dirt cheap prices for that matter. All in all, Pintime watches are not a bad choice when it comes to budget bling. Sleep in a loop, using WFE or WFI (if you're using the Nordic SoftDevice, call sd_app_evt_wait instead). Put the heart rate sensor in sleep mode by setting the PDRIVER (0x0C) register to 0, see the HRS3300 datasheet for details.

SLEEP (reset the touchpanel using the reset pin before using this register: pin_low, delay 5ms, pin_high, delay 50ms then write 3 to register 0xA5) The HRS3300 sensor is enabled on power on. Write byte 0x00 to the PDRIVER register (0x0C) to set it in sleep mode. No these won’t fool anybody up close, but from a distance, and in passing, they do have the glitter and luster of a bust down watch. Definitely not bad for a watch that has no real diamonds in it. The on board accelerometer in devices shipped before July 2021 is a Bosch BMA421, connected to the I2C bus.

Navigation menu

Comfortable and secure fit: The stainless steel band and hidden push-button clasp ensure a comfortable and secure fit. Leave all pins in their default state, except for P0.05 (SPI CS) and P0.25 (LCD CS) which should be configured as an output and set to high. The display is driven using the ST7789 display controller. Use the following pins to drive the screen: Put the SPI flash in deep power-down mode by setting flash CS high, then low, then writing the byte 0xb9 on the SPI bus, and then setting flash CS high again. Some bootloaders might leave the UART enabled after they start the application, leading to high current consumption.

Luxurious and sporty design: The watch has a unique and eye-catching appearance with a diamond CZ embedded in the dial. It is perfect for everyday wear and can withstand splashes and brief immersion in water. There is not a whole lot amazing going on with these builds. Clearly, these are not, by any means high end watches. they are decent, however, for being such low priced timepieces. Chip select must be held low while driving the display. It must be high when using other SPI devices on the same bus (such as external flash storage) so that the display controller won't respond to the wrong commands. But we’re not here to talk about that today. Instead, we are here to talk about this super cheap brand that does not contain any real diamonds yet has the same style of a bust down watch.

🍪 Privacy & Transparency

Note: The part number for the SPI FLASH in the schematic diagram is not correct, the PineTime features a larger external FLASH device, see below. Being this cheap is a good thing, as it takes away some of the potential buyer apprehension. There is not as much to potentially lose, if you are not investing a whole lot of money into a watch anyway. To investigate current consumption, it's a good idea to disable everything possible to get the lowest current consumption possible, and then re-enable things one by one. Here is one way to get a baseline current consumption of 60µA, as measured from the 3.3V pin with the battery disconnected:

Converting this voltage to an estimated capacity in percent requires a more complicated algorithm, because Lithium-ion batteries have a non-linear discharge curve.Gadgetbridge (Android >= 4.4) - Companion mobile app, supports updating firmware/bootloader, send notifications, etc. What you find here in the general build of these watches is nothing special. These are quartz watches, featuring analog displays. The cases are made from metal alloys. Dial windows are typically mineral crystal. The touch panel is controlled by a Hynitron CST816S chips. Unfortunately, there is not much information about this chip on the internet apart from the datasheet below and a reference driver. This is enough to implement a basic driver, but crucial information needed to implement advanced functionalities are missing (I²C protocol and registers, timings, power modes,...). It appears that under some configurations, edge triggered interrupts result in a large power drain. One way to avoid this is by using the pin sense mechanism.

It's often better to avoid floating point values on embedded systems and in this case there is no reason to use float at all, we can just represent the value in millivolts. Therefore the formula can be simplified to: In terms of style, these do hit the mark, and they do present the look that they are going for. Just don’t be surprised if they give away their real value upon closer inspection. If you came here to find something that had the style of an iced out watch, then you will not be disappointed. For what you are paying, you get the styles of frosted diamond encrusted watches, at bargain prices. You’ll want to repeat this method on both immediate sides of the clasp itself as well as for the number of links you want to remove on the other side of the strap.Iced out”, or also known as “bust down” watches refer to watches that are encrusted with diamonds. These styles have become popular among celebrities, especially in the world of hip hop.